Skip to main content
RACELOGIC Support Centre

10 - VBOX Test Suite Chart

Introduction

The 'Chart' tab is where the user can access all the functionality of the chart. This tab will be displayed when the user clicks anywhere on the chart area and will automatically be selected.

Ribbon Bar

VBTS Chart Ribbon.png

Note: Ribbon bar icons may move/ resize dependent on the Software window size.

Data

VBTS Chart Data.png

X-Axis

The 'X-Axis' button allows the user to specify which channel is used for the X-Axis of the selected graph. Selecting the X-Axis button will display a drop down menu of all available channels, plus a calculated channel called ‘Elapsed time’. The user can then select a channel to display on the X-Axis of the selected graph.

Y-Axis

The 'Y-Axis' button allows the user to specify which channel is display as a trace on the graph. Selecting the 'Y-Axis' button will display a drop down menu of all available channels in the file or that are being sent across the live serial stream from a VBOX.

Every time the user selects a channel, a new Y-Axis will be added to the selected chart and a trace of that channel vs the selected X-axis will be displayed (for example speed vs time). The user can add multiple channels, with each channel adding a new trace. Deselecting a channel will remove this trace from the graph.

Smoothing Level

The 'Smoothing Level' button opens a box that allows the user to set the smoothing level of any active channels on the chart. 

Scale

The scale level button opens a box that allows the user to set the y axis scale range of any active channels on the chart. This can either be done by manually setting an upper and lower value, or by ticking the ‘Auto’ option to automatically set the axis to the maximum and minimum value.

Display

VBTS Chart Display.png

Zoom In

The 'Zoom in' button zooms in on the graph, centred on the cursor position.

Zoom Out

The 'Zoom out' button zooms out on the graph, centred on the cursor position.

Reset Zoom

The 'Reset zoom' button returns the graph to full view.

Run Compare

The 'Run Compare' button allows the user to switch between viewing the whole file to individual runs from the results table.

The standard display highlights regions of the graph to indicate where the selected runs occur.
 

VBTS Chart Whole Session.png
Standard display
 

Selecting the ‘Run Compare’ button will then show individual runs from the results table. When a run (or runs) are selected from the results area, those runs will be displayed on the graph with a common origin.

Note: Run Compare will be on by default when in 'Online' mode.
 

If a run starts or ends between data samples, the start and end values will interpolate between samples to provide the desired result. For example, if you are running a Decel Test (60 – 20 mph), any selected runs displayed within the graph will start at 60 mph and end at 20 mph, even if the data samples closest to the test criteria are 60.5 mph and 19.6 mph.


VBTS Chart Run Compare.png
Run Compare selected

Average Only

If ‘Avg’ has been ticked within the results of a test, selecting the 'Average Only' button will display only the average ‘best fit’ curve of all selected runs.

Legend

The 'Legend' button allows the user to display a detailed legend that indicates which file or run each coloured trace belongs to. When the button is pressed, a fly out window will appear from the legend to show the names of any selected files or runs.
 

20.png
 

This expanded legend also allows the user to show and hide the traces from the graph and also to remove the file completely from that test.

Clicking on the colour square will allow the user to change the colour of the related channel traces.

Add Chart

The 'Add chart' button allows the user to add a chart that has an independent x axis from the existing Chart(s).

Line Style

The 'Line Style' button opens a dropdown menu where you can choose whether you would like chart lines to be viewed 'Sharp' (default), which details every deviation, or 'Normal', which provides a slightly smoothed trace. There is also the option to select (default)/ deselect the showing of individual GPS logging points.
 

VBTS Chart Line Style.png

Chart Tool

VBTS Chart Tool.png

Zoom X

The 'Zoom X' button defines how the left click and drag action is performed. When selected, Left clicking and dragging the cursor to the right will perform a horizontal zoom of that area. To return to the full view, simply click and drag the cursor to the left.

Zoom X-Y

The 'Zoom X-Y' button defines how the left click and drag action is performed. When selected, Left clicking and dragging the cursor to the right will perform a ‘box zoom’ of that area. To return to the full view, simply click and drag the cursor to the left.

Pan

The 'Pan' button defines how the left click and drag action is performed. When selected, Left clicking and dragging the cursor will pan the graph accordingly. The pan action is only performed if the graph is zoomed.

Gate

The 'Gate’ area will mirror the gate options available within each test, for more information, view the individual 'Test Page'. If no test is chosen, the Gate area will default to the below: 
 

  VBTS Gate.png

Add Gate (space)

Pressing the ‘Add Gate’ button will add a virtual gate to the chart and map area at the point of the cursor, indicated by green coloured lines. The currently selected gate is indicated by a blue coloured line. Once a gate has been added, the gate width can be specified. A gate can also be added by using the keyboard space button. These gates can then be used as a start or end condition.

IMPORTANT - When adding a gate, the vehicle must be travelling greater than 0.8 km/h in order to ascertain the heading of the gate.

Rename

Allows the user to rename the currently selected gate line (start of bath, end of bath, etc.).

Delete

Deletes the currently selected gate.

Action

VBTS Chart Action.png

Add Marker

Pressing the 'Add Marker' button will add a marker to the chart at the current position of the cursor. Pressing the button again will add a secondary marker and the region between the two markers will be highlighted and allows further actions, such as cut and measure, to be performed. Only two markers can be added to the chart, however once placed, these markers can be moved by clicking and dragging the marker to a new location.

Remove Marker

'Remove Marker' deletes the last marker that was added to the chart.

Mark Region

The 'Mark Region' button changes the left click action of the chart. With the 'Mark Region' button selected, the user can click and drag on the graph to highlight a specific region that can be measured or cut. Selecting the 'Mark Region' button again will change the left click action of the chart to 'Zoom X'.

Cut

The 'Cut' button allows the user to remove a portion of the current file. This can be done in three ways:

  • Cut Before Cursor – Will remove all data from the start of the file up until the cursor location.
  • Cut After Cursor – Will remove all data from the cursor location up until the end of the file.
  • Cut Between Markers – Will remove all data from in between the two marker locations.

Once the cut action has been performed, a warning will appear on the chart that the file contains unsaved changed. To save these changes, click the save within this warning.
 

VBTS Chart Cut.png

Measure

Once a region has been highlighted within the chart area, it is possible to select the ‘Measure’ button. Once pressed, a new window will appear detailing the maximum, minimum and average values of all channels within that window. If a region starts or ends between data samples, the start, end, difference, maximum and minimum values will interpolate between samples to provide the desired result. The average value is computed from sample values only.
 

Double clicking on a 'Min' or 'Max' value will move the chart cursor to that location.
 

measure (1).png
 

It possible to then export the displayed results to either a .csv file or to the clipboard ready to be pasted into another document.

Playback

VBTS Chart Playback.png

Use the playback buttons to play or stop the real time recording of any data along with any associated video.

Note: Not available when the 'Run Compare' button has been seleceted.

Help (F1)

VBTS Help.png
 

Pressing this 'Help' button will automatically open an internet browsing window and load the relevant section of the Racelogic Support Centre. This page will only be displayed if there is a valid internet connection. If there is no valid internet connection, a cached version of the relevant section (from the last software update) will be presented in PDF form. This can also be accessed by using the keyboard shortcut 'F1'.

Chart Functionality

Adding a Channel

VBOX Test Suite allows the user to display multiple channels on their own Y-Axis, as well as having the option to overlay channels from multiple files.

To add a channel to the graph, select the ‘Y-Axis’ button on the chart tab. Selecting this button will show a drop down list of all the channels available in the loaded files. Selecting the tick box next to a channel will automatically add that channel to the active graph on its own separate y-axis.

Note: Added channels will maintain the colour assigned to the run (unless they overlaid and the colours manually changed).


VBTS Chart Add Channel.png
 

Overlaying Channels

VBOX Test suite allows the user to overlay channels to compare the data traces on a common y-axis, for example when looking at Vehicle speed and wheel speeds.

Clicking and holding the mouse button on the channel name in the top left hand part of the relevant chart allows the user to drag that chart onto the chart that they would like to overlay.
 

VBTS Chart Overlaying Channel.png
 

When that channel name is dragged over to another chart, that chart will be framed by a green box to highlight that the user can add that channel to the chart to produce an over lay of the signal traces.
 

VBTS Chart Overlaying Channel2.png
 

By default, all channels will remain the same colour, however the user can change the channel colour by clicking the colour square in the Chart Legend.

To return back to the original view where all channels are on a separate axis, the user can click on the ‘Restore’ button to the right of the combined channels name. 


When a 'Trigger' channel is overlaid with other channels, it will be rescaled dependent on whether the channels are auto or manually scaled:

  • If the other channel(s) is auto scaled, the Trigger will be rescaled to the minimum and maximum values of the channel(s).
  • If the other channel(s) is manually scaled, the Trigger will be rescaled to the minimum value and 90% of the maximum value of the channel(s).

Changing the X-Axis

By default, all graphs will have elapsed time as the x-axis, however the user can choose to change this at any time by selecting the ‘X-Axis’ button on the chart tab. Selecting this button will display a drop down menu of all the available channels in the file that the user can select for the desired x-axis.

By changing the x-axis from continuous (i.e. time) to discreet data will automatically change the graph to display a scatter plot, rather than a line graph.

Navigating Around the Chart

VBOX Test Suite allows the users to zoom in and out of a graph, pan, and navigate from sample to sample and many more via a mixture of mouse clicks, keyboard short cuts and menu buttons.

Zooming

The user is presented with 3 ways to zoom the graph in and out, the first being the button in the Chart tab.
 

VBTS Chart Zoom.png
 

By pressing the ‘Zoom in’ or ‘Zoom out’ button, the graph will zoom in/out by 5%. The user can reset the graph to the default zoom level by pressing the ‘Reset Zoom’ button.

These buttons will also briefly appear next to the chart cursor any time the user clicks/touches anywhere within the chart area. The user can then use these buttons as above.

The final way to zoom is by using the left mouse button. By holding the left mouse button and dragging the cursor to the right, the graph will zoom in ‘horizontally’, where the y-axis remains the same size and only the x-axis changes. To zoom back out, left click and drag the cursor to the left. This returns the graph to its original view.

Saving the Zoom Area

Once zoomed into an area, it is possible to assign the zoomed region to a number by holding the ‘Ctrl’ key and a number key (1 through to 9). Once the region has a number assigned, it is possible to zoom back to that same point by pressing the same number key.

Panning

When zoomed in, it is possible to grab either the x or y axis and drag the axis up/down or left/right. Doing this will pan the graph accordingly.

The user can also hold the right mouse button and drag the graph to pan accordingly, or select the ‘Pan’ button in the ribbon bar and use the left mouse button.

Positioning the Cursor

The graph cursor can be positioned by various different ways. The first and easiest is by simply left clicking anywhere in the graph screen. This will move the cursor to the location that was clicked and display the associated values. The user can also click and drag the cursor left and right with the values constantly updating.

It is also possible to use the arrow keys to move left or right by one pixel at a time, allow the user to scroll through the data continuously.

If the ‘Alt’ key is pressed in conjunction with the arrow keys, the cursor will jump to the next sampled point, rather than just scroll through the interpolated values.

Advanced Controls

The graph area can be controlled in various different ways, as described below:-

Chart Area
Action Mouse Keyboard
Horizontal Zoom In/Out 25 % Wheel Up/Down
Horizontal Zoom In/Out 5 % Alt + Wheel Alt + Up/Down
Vertical Zoom In/Out 25 % Shift + Wheel Shift + Up/Down
Vertical Zoom In/Out 5 % Alt + Shift + Wheel Alt + Shift + Up/Down
Zoom In/Out 25 % Ctrl + Wheel  

Zoom In/Out 5 %

Ctrl + Alt + Wheel  
Horizontal Zoom In Left Click + rubber band Right  
Horizontal Zoom In Full   Ctrl + Up
Horizontal Zoom Out Full Left Click + rubber band Left Ctrl + Down
Vertical Zoom In Shift + Left Click + rubber band Up  
Vertical Zoom In Full   Ctrl + Shift + Up
Vertical Zoom Out Full Shift + Left Click + rubber band Down Ctrl + Shift + Down
Zoom In Ctrl + Left Click + rubber band Right  
Zoom Out Full Ctrl + Left Click + rubber band Left

Backspace

Alt + Ctrl + Shift + End

Pan Right Click + Drag  

Pan with rounding the axis position to labelled ticks

Alt + Right Click + Drag

Ctrl + Alt + Right Click + Drag

 
Move Cursor Left/Right 2 % of view width   Alt + PgUp/PgDn
Move Cursor Left/Right 10 % of view width   PgUp/PgDn
Move Cursor Left/Right 100 % of view width   Ctrl + PgUp/PgDn
Position the Cursor Left Click  
Move the Cursor Left Click Cursor + Drag  
Centre the Cursor in the View   Num.
Switch to Data Series or clear Data Series selection Click on the Series name displayed in the Legend  
Switch to Next Data Series Click on the Series name displayed in the Legend ]
Switch to Previous Data Series Click on the Series name displayed in the Legend [
Move the Legend to another position within the Graph Click the Legend + Drag  
Common
Action Keyboard
Move Cursor One Pixel Left/Right Left/Right
Move Cursor One Sample Left/Right Alt + Left/Right
Move to Previous/Next Marker or Start/End if no markers Ctrl + Left/Right
Move to First/Last Sample in the view or Beginning/End of Selection Home/End
Move to Start/End Ctrl + Home/End
Save the current View (zoom and position) under <Number>

Ctrl + (1-9)

Ctrl + Shift + (1-9)
Restore the View (zoom and position) from <Number> (1-9)
Cut the data before the cursor location Shift + X
Cut the data after the cursor location Ctrl + X
Chart Axis
Action Mouse
Centre the clicked value Double Click
Pan the axis Click + Drag
Pan the axis attracting labelled ticks to the left/bottom edge of the chart Alt + Drag

Save/Copy Image

Right clicking within the Chart area allows the user to either copy the view currently seen within the map window as an image to the computer clipboard, or save locally as a .png, .bmp, .gif, .jpg or .tif file.

Voice Tags

When a logged VBOX data file .vbo is loaded and displayed in the Chart, any associated .wav audio voice tag files will appear below the speed data trace as speaker icons VBTS Voice Tag Icon.png and a vertical line will indicate the exact location of the start of the recording.


The audio files can be played by clicking on the speaker icons. The icon will animate to indicate the audio file is being played.


More information on recording audio tags with a VBOX 3i can be found here.

Video Overview